How Switched Mode Power Supply Works - SMPS - ATX

How Switched Mode Power Supply Works - SMPS - ATX

Clique Aqui: Versão em português

ATX Switched-Mode Power Supplies have some interesting features when compared to standard Switched Mode Power Supply (SMPS).

In the ATX power supply, there are different output voltages: + 12V, + 5V, + 3.3V, -12V, -5V and 5VSB. There are some variations on these types of Power Supply, but in the general context, the pattern is this.

The way SMPS work is pretty much the same.
They control the output voltage by opening and closing the switching circuit so as to maintain the opening and closing time of this circuit, IE the width of the pulses and their frequencies, to obtain the desired voltage.

There are separate processes for everything to work smoothly.

So let's see the modular diagram to unravel steps of these processes, so that we can step by step understand.

This is the block in modules divided by steps, to improve our understanding.

There are 10 basic steps to running an ATX power supply, there are other underlying modules that are intrinsic in the steps, but, we'll not go as deep as it would be extremely great this Blogger, for those who want to watch the explanatory video with details on our channel from YouTube.

So let's understand these steps:

Step 1 - Transient Filter


It is by this stage that the voltage coming from your network, whether 110 or 220V AC should enter.

Transient Filter

This voltage goes through a basic protection, the fuse, that if some step ahead short, the fuse opens, avoiding to burst everything ahead, and in the same line, we have the NTC (Negative Temperature Coefficient), It's a surge current limiter, in series with the electric circuit,

In it the value of ohmic resistance decreases as its temperature rises, its initial resistance is approximately 15 Ohms, which we can understand by the Ohms' law, the advantages one has in using it in series, after the power supply switches it on lowers its resistance to approximately 0.5 Ohms.

EMI filters also exist, these are used to avoid high frequency noise and a huge amount of harmonics generated by the switches that can propagate through the electrical network and cause interference in nearby electronic equipment.

Step 2 - Primary Rectification

Primary Rectification

In this stage we find the rectifier bridge, or an arrangement formed by four common diodes, which has the function of rectifying a full-wave voltage, that is, rectifying an alternating electric current (AC), transforming it into a continuous electric current ( A.D).

Step 3 - Filtration

Filtration

After rectification, the DC signal, Riples (which are small variations, the capacitors are responsible for the filtering and stabilization IE, decrease of these Riples, in the rectified voltage, this voltage rises to something around 300V, which are used in the power switches, this part is fundamental to the correct stabilization of the source especially if its source is of high power.

Step 4 - Power Switches

Power Switches

These switches can be Bipolar Power Transistors such as MOSFETs, or any other type, but they differ from ordinary transistors, by the type of operation in which these transistors work, these switching transistors dissipate less power than a common working transistor in a linear source because they work as a switch on / off at high speeds, depending on the design of the source, they suffer variations that are usually between 20Khz to 100kHz, they are directly responsible for the output voltage, and stability of that voltage, through of the commands received by the Control Circuit.

Step 5 - Output Transformer

Output Transformer

The transformer is a high frequency CHOPPER TRANSFORMER, and they also work with alternating voltage, when passing through the switches the voltage will be a square wave AC type PWM, but with high frequency, not with the same frequency of 60Hz of the input voltage.

The switches work on two different levels, High and Low, when it is HIGH, the voltage goes through it normally, causing a constant voltage level in the input of the coil of the transformer, the action of these transistors, go from HIGH to LOW very quickly.

This will induce the winding to have the necessary voltages according to the winding and frequency placed on these switches.

Step 6 - Fast Rectifier

Fast Rectifier

With the voltage generated by high frequency switches, a diode is needed to meet this demand, so we have the high speed diodes called SCHOTTKY DIODES or fast recovery diodes since ordinary diodes would not be able to work with high frequency voltages .

Step 7 - Output Filters

Output Filters

The inductor - Which has the function of eliminating the high frequency harmonics, so that they do not travel to the equipment that will be fed, for imagine you, if these harmonics pass to a micro-controller for example, could cause undue loads loads and errors of reading in the control processes.

And the Capacitors - They are the ones that filter and stabilize the voltage at the output, avoiding ripples and instabilities at the output.

Step 8 - Driver Transformer

Driver Transformer

The driver transformer in this case is nothing less than the one responsible for traffic the information coming from the Integrated Circuit Controller, and pass these commands to the switches, so as to bring insulation or electrical decoupling between primary and secondary, in this topology there is a pair of transistors that also switch the Transformer Drive to receive these PWM pulses from the driver IC, passing this information to the power step we already saw in Step 4.

Step 9 - PWM control

PWM control

The brain of a switched source is its PWM controller, they are dedicated integrated circuits, to perform that work, but they do not work alone, there are also current sensors, which also vary from source to source, but it is very likely that you will find in its source the TL341 IC, it has the aspect of a transistor, but, it is not a transistor, it is very popular for its cost benefit.

This circuit is connected to the output of the power supply, receives Feedback and directs the voltage information to the IC that controls the oscillator that generates a rectangular signal whose pulse width is controlled and sent to the Transformer Drive that sends these commands to the step of power.

If the power at the output to raise the voltage tends to drop, the circuit activates the instantaneous correction in the pulse width of the switching transistors and the voltage keeps stabilized.

Step 10 – Primary Power Supply VSB

Primary Power Supply VSB

VSB stands for Voltage Standby, which is technically a power supply that keeps its output active, whenever the source power cord is connected to the mains, its capacity is approximately 2 Amps, and this depends on the total power of the source, this active voltage line is to keep the circuit active and is necessary for when the power on button is activated through PSON, which is the start of the power supply, then the oscillator will activate the power line also powers the motherboard hardware to activate peripherals via software, keyboard, network, and so on.

Thank you, subscribe to our Blog and our channel on YouTube and our social networks.

See you later.

Please subscribe!!! Click FVM Learning

God bless you.

Shalom